DOKTER IT: routing OSPF packet tracer

A. pendahuluan Gambar terkait

1. pengertian

packet tracer adalah simulasi membuat topolgi

2. latar belakang

karena packet tracer lebih efektif karena dapat di konfigurasi

3. maksud dan tujuan

agar kita tahu fungsi sebenarnya dari packet tracer bukan untuk main main

B. waktu

20 menit

C. alat dan bahan

laptop
packet tracer
listrik

D. pelaksanaan

Pertama kita buat dulu sebuah jaringan , seperti gambar dibawah.....

Selanjutnya..
berikan IP Address pada setiap PC..
1. PC 1 dengan nama "PC0"..

2. PC 2 dengan nama "PC 2"..

3. PC 3 dengan nama "PC 3"..

Tahap selanjutnya berikan IP Address pada setiap router . Contoh sebagai berikut :

Pemberian IP Address di Router 1

     --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.18.8.1 255.255.0.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 192.168.8.1 255.255.255.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Konfigurasi EIGRP pada Router 1,

Router(config)#router ospf 4
Router(config)#router-id 2.2.2.2
Router(config-router)#net 172.18.8.0 0.0.255.255 area 0
Router(config-router)#net 192.168.8.0 0.0.0.255 area 0
Router(config-router)#log-adjacency
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

Pemberian IP Address di Router 2

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.19.9.1 255.255.0.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 192.168.8.2 255.255.255.0
Router(config-if)#band 125
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Router(config-if)#exit
Router(config)#int se3/0
Router(config-if)#ip add 18.8.8.1 255.0.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit

Konfigurasi OSPF pada Router 2,

Router(config)#router ospf 4
Router(config-router)#net 172.19.9.1 0.0.255.255 area 0
Router(config-router)#net 192.168.8.0 0.0.0.255 area 0
Router(config-router)#net 18.8.8.0 0.255.255.255 area 1
Router(config-router)#log-adjacency
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

Pemberian IP Address di Router 3

     --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.10.1 255.255.0.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 18.8.8.2 255.0.0.0
Router(config-if)#band 125
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Konfigurasi OSPF pada Router 3,

Router(config)#router ospf 4
Router(config)#router-id 4.4.4.4
Router(config-router)#net 172.16.10.0 0.0.255.255 area 1
Router(config-router)#net 18.8.8.0 0.255.255.255 area 1
Router(config-router)#log-adjacency
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

Setelah dikonfigurasi, coba di ping antara PC0 , PC1 dan PC2..

SELAMAT MENCOBA................

Apabila kurang jelas bisa di tanyakan.................